- The outdoor switchgear
- The metal switchgear and RMU
- The switchgear components
- The power transformer and CT PT
- Solutions for power and grid
Power Distribution Transformer Questions and Answers
2020-11-02 16:04:00 Copyfrom：本站 view:106
What does △/ Y0―11 mean which is showed on the transformer nameplate?
According to the connection mode of transformer primary and secondary coils, the voltage phase Angle of transformer primary and secondary side lines is different. △/ Y0 - 11 indicates the phase Angle difference between the two line voltages of the transformer is 330° in the customary clock notation that is 11 o 'clock.
The primary and secondary of the power transformer often have two or more coils each, such as the coil with the same polarity end sign lost, what method can be used to identify?
The same polarity end of each coil of the power transformer is usually indicated by the symbol "*".If the mark is missing, it can be identified experimentally.First, either end of one low-voltage coil and another low-voltage coil is connected to the power supply of any high-voltage coil. Then, the voltmeter is used to measure the voltage of the remaining two ends of the two low-voltage coils. If the voltage measured is the sum of the voltages of two low-voltage coils, it indicates that the two ends of the connection are not of the same polarity; if the voltage measured is the difference between the two, it indicates that the two ends of the connection are of the same polarity.The method for determining the polarity of high voltage coils can be deduced in this way.
If the input voltage of the transformer is excessively greater than the rated voltage, what is the effect on the transformer?
Generally, the flux density of transformer is higher when rated, and the core tends to saturation.If the input voltage is more than the rated voltage, the core will be excessively saturated, resulting in the deformation of the output voltage waveform, which contains a large number of high-order harmonic components, resulting in the increase of the output voltage amplitude, and the insulation of the coil is easy to damage.At the same time, the increase of magnetic flux density increases the iron loss and the corresponding increase of no-load current, resulting in transformer heating and affecting the power factor of the grid. Therefore, the input voltage of the transformer is generally not allowed to exceed 5% of the rated voltage.
Transformers are stationary equipment, but they hum when they are in operation. Why?
When the transformer coil is connected to 50hz AC, 50hz flux is also generated in the core.Due to the change of magnetic flux, the silicon steel in the core also vibrates accordingly, even when clamped, producing a buzz of 50hz vibration.But as long as the sound is not increased, and there is no other noise, it is normal.
Why should the core clamping bolt of power transformer be insulated from the core?
The core of the transformer is made of silicon steel.In order to reduce the core eddy current loss, the silicon steel plates are insulated from each other. If the core clamping bolts are not insulated from the core, it is bound to cause a short circuit at the bolt and increase the core eddy current loss.
Why adopting disk shaped winding instead of barrel shaped winding in large transformer?
Because the short circuit current of large transformer is large, the stress generated by short circuit is also large, the disk winding can be added with more supports without causing the deformation of the coil. Large transformer heat, disk winding have more oil channels and the heat dissipation is good, barrel winding only have the oil channel between high and low voltage, the heat dissipation is poor.
Why should the coils of a large capacity transformer be transposed?
As the coil of this type of transformer is usually wound with several wires, because the diameter of the coil is large, the length of the wire in the inner and outer rings is much different, so the length of each wire is different.Transposition can make each wire has the same length and ensure the coil resistance balance.
The wires in the inner and outer rings have different reactance value due to the different magnetic field. Transposition allows the wires to be in a similar position in the magnetic field to reduce additional losses in the coil.
Transformer coils are immersed in transformer oil, so can transformer coils be treated without paint?
The insulation part of the transformer is paper, cardboard, cotton yarn, etc., its insulation performance has been improved after being immersed in oil. Therefore, only from the point of view of the insulation requirements of the transformer, the transformer soaked transformer oil after vacuum drying , can achieve a very high insulation voltage.
Why is there a flexible connection between the bus connections of transformer porcelain bushing in substation?
Because the bus is fixed, and the position of the transformer may be slightly moved due to maintenance and other reasons. At the same time, the bus also has the performance of thermal expansion and cold contraction. After the flexible connecting device is installed, the relative position of the bus and the transformer can be slightly changed, which will not cause great stress and damage the porcelain bushing of the transformer.
Why are power transformer tap changers usually installed on the high voltage side?
Since the current on the low-voltage side is much larger than that on the high-voltage side, the area of the wire required for the tap and the size of the tap switch should be increased accordingly.In this way, not only lead wire joint is not convenient, but also the installation position must be increased.The low voltage coil of core transformer is in the inner side, so it is difficult to draw the tap from the low voltage side.At the same time, the number of turns of the general low-voltage winding is less than the high-voltage winding, therefore, the tap voltage unless it is a turn of the induction voltage integer times, otherwise there is a correct access to the tap voltage.Therefore, the general power transformer tap, are installed in the high voltage side.
For the middle line bushing of a power transformer used in a power transformer in a large current grounded system, is it ok to use a low level of insulation bushing?
A power transformer used in a large current grounded system in which the wire remains at zero potential (except in certain fault cases) but cannot be connected directly to the ground as often as is required by the operation mode, so a lower level of insulation may be used.This will reduce the cost.However, when this is done, the power transformer cannot be tested for preventive insulation resistance at its rated voltage class, since the neutral point has the same potential as the outgoing line when the coil is pressurized.Therefore, the reliability of the transformer cannot be fully tested in the preventive test.
Why do we use flat tubes instead of round tubes for power transformer heat pipes?
When the heat dissipation area of the flat pipe is equal to that of the round pipe, the insulation oil in the flat pipe is less than that in the round pipe.That is to say, the amount of oil per unit heat dissipation area of the flat tube is less than that of the round tube. In other words, the flat tube can achieve the same heat dissipation effect with less oil than the round tube.Therefore, the current transformer heat pipe are used flat pipe instead of round pipe.
Auto Relcoser and Outdoor SF6 LBS in Tanzania
33kV Bulk metering unit in Uganda
No.6: Smart SCADA solution achieve greatly cost saving by reducing power line losses !
Bangladesh Turnkey Substation project completed successfully
Completed KE Turnkey project
Rockwill Group products in west africa
110kV substation completed in Afghanistan
Rockwill's substation was completed in congo and run well
ANSI/IEEE C37.60 Standard Auto Recloser in Venezuela
Popular solid type Auto recloser for Cambodia
Nowadays exceed 1200 number Auto reclosers running in Africa
Economical type Auto recloser is well running in Philippines
Recloser with Smart system good reputation influenced in Vietnam
New type solid insulation Load break switch in Indonesia
The first lot MV switchgear go to service for Korea
Best solution for your power!
Copyright © 2018 Rockwill Electric Group Co.,Ltd. All Rights Reserved.